ASP 50 to 320

A cooling tower is a device that is designed to transfer heat from the specific manufacturing process of the atmosphere by the means of heat dissipation evaporative by lowering the temperature of the circulating water.

All models FUTURE ASPIRATION) 50, 80, 110, 140, 200, 270 320with a circulation of air being sucked into the current of the water, and have a vent in a way that is induced, that is, from the inside to the outside, with funding from the air, the landscape, and the discharge of the air in the vertical upward movement through the axial fan with low power consumption. Manufactured in GRP (Polyester Reinforced with Fiber Glass), are characterized by a high resistance to corrosion and they are designed in a variety of sizes, it can also be the most compact for fitting in tight spaces, being shipped fully assembled, there is no need for the execution of the services, assembly and installation in the field, that is, the plug-in to play.

Get in touch with the team at the ALFATERM and schedule a service visit from one of our experienced engineers!

ASP 50

Connections
Model		ASP 50
A		500
B		670
C		670
D		840
E		840
F		1540
G		1860
H		150
I		895
J		100
L		280
M		1170
N		1360
O		50
	V	1"
	W	1"
	X	2"
	Y	2"
	Z	3/4"
The Volume of the water in the bowl	(L)	115
With the fan weight (KG)	Emb.	125
With the fan weight (KG)	Oper.	330

01.

THE CONNECTION TO THE V = DRAIN, THREADED BSP

02.

CONNECT W OVERFLOW, THE THREAD BSP

03.

THE CONNECTION TO THE X = THE ENTRANCE TO THE HOT WATER THROUGH THE HOSE AND RUBBER

04.

THE CONNECTION OF THE Y = OUTPUT OF COLD WATER THROUGH THE HOSE AND RUBBER

05.

CONNECTION TO Z-THE ENTRANCE TO THE WATER OF A REPLACEMENT, FAUCET SINGLE)

06.

CONNECTIONS TO THE INLET AND THE OUTLET OF THE WATER THROUGH THE HOSE AND RUBBER

07.

ALL DIMENSIONS IN MILIMENTROS (MM)

08.

L. F. = MAXIMUM SUPPLY ALFATERM

09.

PROVIDE SUPPORT TO THE PIPING

10.

THE CONSTRUCTION OF THE SUPPORT BASE OF THE TOWER IS EXPECTED TO BE IN THE CONCRETE / MASONRY, FLAT, SMOOTH AND LEVEL, AND THE RESPONSIBILITY OF THE CUSTOMER

11.

ANY OBSTACLE IN THE VICINITY OF THE TOWER, YOU MUST HAVE THE APPROVAL OF THE ALFATERM

12.

THE PRESSURE REQUIRED AT THE INLET OF THE DOMESTIC HOT WATER, ACCORDING TO THE DATA SHEET

13.

'COLOR' = - FILLING-TYPE BLOCKS AND BARS IN THE SHAPE OF THE WAVES CROSSED, POLYPROPYLENE, POLYPROPYLENE, ANTI-FLAME, V-0 OR POLYPROPYLENE, ANTI-FLAME AND V-2

14.

'BUS RAPID TRANSIT'=, FILLING TYPE, THE BARS OF A DROP-TUBE, POLYPROPYLENE, POLYPROPYLENE, ANTI-FLAME, V-0 OR POLYPROPYLENE, ANTI-FLAME AND V-2

15.

'PUT'=, FILLING TYPE, BLOCKS, FILM, PVC,

16.

TROUGH SINK FOR DROP, BUILT-IN

17.

OBSERVE THE MINIMUM DISTANCE AND A MAXIMUM HEIGHT OF 1500 MM FOR WALLS AND OBSTACLES

18.

SUBJECT TO CHANGE WITHOUT NOTICE PRIOR

19.

THE HEIGHTS OF THE "F" AND "G" FOR UP TO 3 LAYERS OF FILLING

An example of a specification

Aspiration	ASP
Model	50
Number of layers of filler	2
Engine power	5
No. of poles in the motor	8
Type of filler	COLOR
Axial fan	A

ASP-80

Connections
Model		ASP-80
A		550
B		870
C		870
D		1040
E		1040
F		1750
G		2120
H		160
I		1020
J		100
L		310
M		1370
N		1370
O		50
	V	1"
	W	1"
	X	2"
	Y	2"
	Z	3/4"
The Volume of the water in the bowl	(L)	220
with the fan weight (KG)	Emb.	150
with the fan weight (KG)	Oper.	470

01.

THE CONNECTION TO THE V = DRAIN, THREADED BSP

02.

CONNECT W OVERFLOW, THE THREAD BSP

03.

THE CONNECTION TO THE X = THE ENTRANCE TO THE HOT WATER THROUGH THE HOSE AND RUBBER

04.

THE CONNECTION OF THE Y = OUTPUT OF COLD WATER THROUGH THE HOSE AND RUBBER

05.

CONNECTION TO Z-THE ENTRANCE TO THE WATER OF A REPLACEMENT, FAUCET SINGLE)

06.

CONNECTIONS TO THE INLET AND THE OUTLET OF THE WATER THROUGH THE HOSE AND RUBBER

07.

ALL DIMENSIONS IN MILIMENTROS (MM)

08.

L. F. = MAXIMUM SUPPLY ALFATERM

09.

PROVIDE SUPPORT TO THE PIPING

10.

THE CONSTRUCTION OF THE SUPPORT BASE OF THE TOWER IS EXPECTED TO BE IN THE CONCRETE / MASONRY, FLAT, SMOOTH AND LEVEL, AND THE RESPONSIBILITY OF THE CUSTOMER

11.

ANY OBSTACLE IN THE VICINITY OF THE TOWER, YOU MUST HAVE THE APPROVAL OF THE ALFATERM

12.

THE PRESSURE REQUIRED AT THE INLET OF THE DOMESTIC HOT WATER, ACCORDING TO THE DATA SHEET

13.

'COLOR' = - FILLING-TYPE BLOCKS AND BARS IN THE SHAPE OF THE WAVES CROSSED, POLYPROPYLENE, POLYPROPYLENE, ANTI-FLAME, V-0 OR POLYPROPYLENE, ANTI-FLAME AND V-2

14.

'BUS RAPID TRANSIT'=, FILLING TYPE, THE BARS OF A DROP-TUBE, POLYPROPYLENE, POLYPROPYLENE, ANTI-FLAME, V-0 OR POLYPROPYLENE, ANTI-FLAME AND V-2

15.

'PUT'=, FILLING TYPE, BLOCKS, FILM, PVC,

16.

TROUGH SINK FOR DROP, BUILT-IN

17.

OBSERVE THE MINIMUM DISTANCE AND A MAXIMUM HEIGHT OF 1500 MM FOR WALLS AND OBSTACLES

18.

SUBJECT TO CHANGE WITHOUT NOTICE PRIOR

19.

THE HEIGHTS OF THE "F" AND "G" FOR UP TO 3 LAYERS OF FILLING

An example of a specification

Aspiration	ASP
Model	80
Number of layers of filler	2
Engine power	5
No. of poles in the motor	8
Type of filler	COLOR
Axial fan	A

ASP 110

Connections
Model		ASP 110
A		670
B		1040
C		1040
D		1170
E		1170
F		2280
G		2760
H		200
I		1300
J		120
L		320
M		1540
N		1540
O		50
	V	1"
	W	2"
	X	3"
	Y	3"
	Z	3/4"
The Volume of the water in the bowl	(L)	315
with the fan weight (KG)	Emb.	280
with the fan weight (KG)	Oper.	770

01.

THE CONNECTION TO THE V = DRAIN, THREADED BSP

02.

CONNECT W OVERFLOW, THE THREAD BSP

03.

THE CONNECTION TO THE X = THE ENTRANCE TO THE HOT WATER THROUGH THE HOSE AND RUBBER

04.

THE CONNECTION OF THE Y = OUTPUT OF COLD WATER THROUGH THE HOSE AND RUBBER

05.

CONNECTION TO Z-THE ENTRANCE TO THE WATER OF A REPLACEMENT, FAUCET SINGLE)

06.

CONNECTIONS TO THE INLET AND THE OUTLET OF THE WATER THROUGH THE HOSE AND RUBBER

07.

ALL DIMENSIONS IN MILIMENTROS (MM)

08.

L. F. = MAXIMUM SUPPLY ALFATERM

09.

PROVIDE SUPPORT TO THE PIPING

10.

THE CONSTRUCTION OF THE SUPPORT BASE OF THE TOWER IS EXPECTED TO BE IN THE CONCRETE / MASONRY, FLAT, SMOOTH AND LEVEL, AND THE RESPONSIBILITY OF THE CUSTOMER

11.

ANY OBSTACLE IN THE VICINITY OF THE TOWER, YOU MUST HAVE THE APPROVAL OF THE ALFATERM

12.

THE PRESSURE REQUIRED AT THE INLET OF THE DOMESTIC HOT WATER, ACCORDING TO THE DATA SHEET

13.

'COLOR' = - FILLING-TYPE BLOCKS AND BARS IN THE SHAPE OF THE WAVES CROSSED, POLYPROPYLENE, POLYPROPYLENE, ANTI-FLAME, V-0 OR POLYPROPYLENE, ANTI-FLAME AND V-2

14.

'BUS RAPID TRANSIT'=, FILLING TYPE, THE BARS OF A DROP-TUBE, POLYPROPYLENE, POLYPROPYLENE, ANTI-FLAME, V-0 OR POLYPROPYLENE, ANTI-FLAME AND V-2

15.

'PUT'=, FILLING TYPE, BLOCKS, FILM, PVC,

16.

TROUGH SINK FOR DROP, BUILT-IN

17.

OBSERVE THE MINIMUM DISTANCE AND A MAXIMUM HEIGHT OF 1500 MM FOR WALLS AND OBSTACLES

18.

SUBJECT TO CHANGE WITHOUT NOTICE PRIOR

19.

THE HEIGHTS OF THE "F" AND "G" FOR UP TO 3 LAYERS OF FILLING

An example of a specification

Aspiration	ASP
Model	110
Number of layers of filler	2
Engine power	5
No. of poles in the motor	8
Type of filler	COLOR
Axial fan	A

The ASP 140

Connections
Model		The ASP 140
A		670
B		1100
C		1100
D		1320
E		1320
F		2350
G		2760
H		200
I		1300
J		120
L		320
M		1600
N		1600
O		50
	V	1"
	W	2"
	X	3"
	Y	3"
	Z	3/4"
The Volume of the water in the bowl	(L)	350
with the fan weight (KG)	Emb.	330
with the fan weight (KG)	Oper.	890

01.

THE CONNECTION TO THE V = DRAIN, THREADED BSP

02.

CONNECT W OVERFLOW, THE THREAD BSP

03.

THE CONNECTION TO THE X = THE ENTRANCE TO THE HOT WATER THROUGH THE HOSE AND RUBBER

04.

THE CONNECTION OF THE Y = OUTPUT OF COLD WATER THROUGH THE HOSE AND RUBBER

05.

CONNECTION TO Z-THE ENTRANCE TO THE WATER OF A REPLACEMENT, FAUCET SINGLE)

06.

CONNECTIONS TO THE INLET AND THE OUTLET OF THE WATER THROUGH THE HOSE AND RUBBER

07.

ALL DIMENSIONS IN MILIMENTROS (MM)

08.

L. F. = MAXIMUM SUPPLY ALFATERM

09.

PROVIDE SUPPORT TO THE PIPING

10.

THE CONSTRUCTION OF THE SUPPORT BASE OF THE TOWER IS EXPECTED TO BE IN THE CONCRETE / MASONRY, FLAT, SMOOTH AND LEVEL, AND THE RESPONSIBILITY OF THE CUSTOMER

11.

ANY OBSTACLE IN THE VICINITY OF THE TOWER, YOU MUST HAVE THE APPROVAL OF THE ALFATERM

12.

THE PRESSURE REQUIRED AT THE INLET OF THE DOMESTIC HOT WATER, ACCORDING TO THE DATA SHEET

13.

'COLOR' = - FILLING-TYPE BLOCKS AND BARS IN THE SHAPE OF THE WAVES CROSSED, POLYPROPYLENE, POLYPROPYLENE, ANTI-FLAME, V-0 OR POLYPROPYLENE, ANTI-FLAME AND V-2

14.

'BUS RAPID TRANSIT'=, FILLING TYPE, THE BARS OF A DROP-TUBE, POLYPROPYLENE, POLYPROPYLENE, ANTI-FLAME, V-0 OR POLYPROPYLENE, ANTI-FLAME AND V-2

15.

'PUT'=, FILLING TYPE, BLOCKS, FILM, PVC,

16.

TROUGH SINK FOR DROP, BUILT-IN

17.

OBSERVE THE MINIMUM DISTANCE AND A MAXIMUM HEIGHT OF 1500 MM FOR WALLS AND OBSTACLES

18.

SUBJECT TO CHANGE WITHOUT NOTICE PRIOR

19.

THE HEIGHTS OF THE "F" AND "G" FOR UP TO 3 LAYERS OF FILLING

An example of a specification

Aspiration	ASP
Model	140
Number of layers of filler	2
Engine power	5
No. of poles in the motor	8
Type of filler	COLOR
Axial fan	A

ASP-200

Connections
Model		ASP-200
A		890
B		1390
C		1390
D		1530
E		1530
F		2350
G		2760
H		200
I		1270
J		140
L		320
M		1890
N		1890
O		50
	V	1"
	W	2"
	X	4"
	Y	4"
	Z	1"
The Volume of the water in the bowl	(L)	570
with the fan weight (KG)	Emb.	520
with the fan weight (KG)	Oper.	1350

01.

THE CONNECTION TO THE V = DRAIN, THREADED BSP

02.

CONNECT W OVERFLOW, THE THREAD BSP

03.

THE CONNECTION TO THE X = THE ENTRANCE TO THE HOT WATER THROUGH THE HOSE AND RUBBER

04.

THE CONNECTION OF THE Y = OUTPUT OF COLD WATER THROUGH THE HOSE AND RUBBER

05.

CONNECTION TO Z-THE ENTRANCE TO THE WATER OF A REPLACEMENT, FAUCET SINGLE)

06.

CONNECTIONS TO THE INLET AND THE OUTLET OF THE WATER THROUGH THE HOSE AND RUBBER

07.

ALL DIMENSIONS IN MILIMENTROS (MM)

08.

L. F. = MAXIMUM SUPPLY ALFATERM

09.

PROVIDE SUPPORT TO THE PIPING

10.

THE CONSTRUCTION OF THE SUPPORT BASE OF THE TOWER IS EXPECTED TO BE IN THE CONCRETE / MASONRY, FLAT, SMOOTH AND LEVEL, AND THE RESPONSIBILITY OF THE CUSTOMER

11.

ANY OBSTACLE IN THE VICINITY OF THE TOWER, YOU MUST HAVE THE APPROVAL OF THE ALFATERM

12.

THE PRESSURE REQUIRED AT THE INLET OF THE DOMESTIC HOT WATER, ACCORDING TO THE DATA SHEET

13.

'COLOR' = - FILLING-TYPE BLOCKS AND BARS IN THE SHAPE OF THE WAVES CROSSED, POLYPROPYLENE, POLYPROPYLENE, ANTI-FLAME, V-0 OR POLYPROPYLENE, ANTI-FLAME AND V-2

14.

'BUS RAPID TRANSIT'=, FILLING TYPE, THE BARS OF A DROP-TUBE, POLYPROPYLENE, POLYPROPYLENE, ANTI-FLAME, V-0 OR POLYPROPYLENE, ANTI-FLAME AND V-2

15.

'PUT'=, FILLING TYPE, BLOCKS, FILM, PVC,

16.

TROUGH SINK FOR DROP, BUILT-IN

17.

OBSERVE THE MINIMUM DISTANCE AND A MAXIMUM HEIGHT OF 1500 MM FOR WALLS AND OBSTACLES

18.

SUBJECT TO CHANGE WITHOUT NOTICE PRIOR

19.

THE HEIGHTS OF THE "F" AND "G" FOR UP TO 3 LAYERS OF FILLING

An example of a specification

Aspiration	ASP
Model	200
Number of layers of filler	2
Engine power	5
No. of poles in the motor	8
Type of filler	COLOR
Axial fan	A

ASP 270

Connections
Model		ASP 270
A		1010
B		1550
C		1550
D		1720
E		1720
F		2350
G		2850
H		200
I		1320
J		160
L		320
M		2070
N		2070
O		50
	V	1"
	W	2"
	X	4"
	Y	6"
	Z	1"
The Volume of the water in the bowl	(L)	720
with the fan weight (KG)	Emb.	610
with the fan weight (KG)	Oper.	1650

01.

THE CONNECTION TO THE V = DRAIN, THREADED BSP

02.

CONNECT W OVERFLOW, THE THREAD BSP

03.

THE CONNECTION TO THE X = THE ENTRANCE TO THE HOT WATER THROUGH THE HOSE AND RUBBER

04.

THE CONNECTION OF THE Y = OUTPUT OF COLD WATER THROUGH THE HOSE AND RUBBER

05.

CONNECTION TO Z-THE ENTRANCE TO THE WATER OF A REPLACEMENT, FAUCET SINGLE)

06.

CONNECTIONS TO THE INLET AND THE OUTLET OF THE WATER THROUGH THE HOSE AND RUBBER

07.

ALL DIMENSIONS IN MILIMENTROS (MM)

08.

L. F. = MAXIMUM SUPPLY ALFATERM

09.

PROVIDE SUPPORT TO THE PIPING

10.

THE CONSTRUCTION OF THE SUPPORT BASE OF THE TOWER IS EXPECTED TO BE IN THE CONCRETE / MASONRY, FLAT, SMOOTH AND LEVEL, AND THE RESPONSIBILITY OF THE CUSTOMER

11.

ANY OBSTACLE IN THE VICINITY OF THE TOWER, YOU MUST HAVE THE APPROVAL OF THE ALFATERM

12.

THE PRESSURE REQUIRED AT THE INLET OF THE DOMESTIC HOT WATER, ACCORDING TO THE DATA SHEET

13.

'COLOR' = - FILLING-TYPE BLOCKS AND BARS IN THE SHAPE OF THE WAVES CROSSED, POLYPROPYLENE, POLYPROPYLENE, ANTI-FLAME, V-0 OR POLYPROPYLENE, ANTI-FLAME AND V-2

14.

'BUS RAPID TRANSIT'=, FILLING TYPE, THE BARS OF A DROP-TUBE, POLYPROPYLENE, POLYPROPYLENE, ANTI-FLAME, V-0 OR POLYPROPYLENE, ANTI-FLAME AND V-2

15.

'PUT'=, FILLING TYPE, BLOCKS, FILM, PVC,

16.

TROUGH SINK FOR DROP, BUILT-IN

17.

OBSERVE THE MINIMUM DISTANCE AND A MAXIMUM HEIGHT OF 1500 MM FOR WALLS AND OBSTACLES

18.

SUBJECT TO CHANGE WITHOUT NOTICE PRIOR

19.

THE HEIGHTS OF THE "F" AND "G" FOR UP TO 3 LAYERS OF FILLING

An example of a specification

Aspiration	ASP
Model	270
Number of layers of filler	2
Engine power	5
No. of poles in the motor	8
Type of filler	COLOR
Axial fan	A

ASP 320

Connections
Model		ASP 320
A		1010
B		1800
C		1800
D		1940
E		1940
F		2350
G		2850
H		200
I		1320
J		160
L		320
M		2270
N		2270
O		50
	V	1"
	W	2"
	X	4"
	Y	6"
	Z	1"
The Volume of the water in the bowl	(L)	920
with the fan weight (KG)	Emb.	780
with the fan weight (KG)	Oper.	1950

01.

THE CONNECTION TO THE V = DRAIN, THREADED BSP

02.

CONNECT W OVERFLOW, THE THREAD BSP

03.

THE CONNECTION TO THE X = THE ENTRANCE TO THE HOT WATER THROUGH THE HOSE AND RUBBER

04.

THE CONNECTION OF THE Y = OUTPUT OF COLD WATER THROUGH THE HOSE AND RUBBER

05.

CONNECTION TO Z-THE ENTRANCE TO THE WATER OF A REPLACEMENT, FAUCET SINGLE)

06.

CONNECTIONS TO THE INLET AND THE OUTLET OF THE WATER THROUGH THE HOSE AND RUBBER

07.

ALL DIMENSIONS IN MILIMENTROS (MM)

08.

L. F. = MAXIMUM SUPPLY ALFATERM

09.

PROVIDE SUPPORT TO THE PIPING

10.

THE CONSTRUCTION OF THE SUPPORT BASE OF THE TOWER IS EXPECTED TO BE IN THE CONCRETE / MASONRY, FLAT, SMOOTH AND LEVEL, AND THE RESPONSIBILITY OF THE CUSTOMER

11.

ANY OBSTACLE IN THE VICINITY OF THE TOWER, YOU MUST HAVE THE APPROVAL OF THE ALFATERM

12.

THE PRESSURE REQUIRED AT THE INLET OF THE DOMESTIC HOT WATER, ACCORDING TO THE DATA SHEET

13.

'COLOR' = - FILLING-TYPE BLOCKS AND BARS IN THE SHAPE OF THE WAVES CROSSED, POLYPROPYLENE, POLYPROPYLENE, ANTI-FLAME, V-0 OR POLYPROPYLENE, ANTI-FLAME AND V-2

14.

'BUS RAPID TRANSIT'=, FILLING TYPE, THE BARS OF A DROP-TUBE, POLYPROPYLENE, POLYPROPYLENE, ANTI-FLAME, V-0 OR POLYPROPYLENE, ANTI-FLAME AND V-2

15.

'PUT'=, FILLING TYPE, BLOCKS, FILM, PVC,

16.

TROUGH SINK FOR DROP, BUILT-IN

17.

OBSERVE THE MINIMUM DISTANCE AND A MAXIMUM HEIGHT OF 1500 MM FOR WALLS AND OBSTACLES

18.

SUBJECT TO CHANGE WITHOUT NOTICE PRIOR

19.

THE HEIGHTS OF THE "F" AND "G" FOR UP TO 3 LAYERS OF FILLING

An example of a specification

Aspiration	ASP
Model	320
Number of layers of filler	2
Engine power	5
No. of poles in the motor	8
Type of filler	COLOR
Axial fan	A